An Error Occurred While Reading the Disk 301001
Samsung Data Migration is a software that allows users to clone HDD or SSD to Samsung branded SSD. It is the easiest way to switch if yous are irresolute, just the hard bulldoze. When I was trying to clone my primary segmentation, I received a message — Cloning Failed, An mistake occurred while reading the disk. It was surprising because I had cloned information technology earlier, and this was my second time. And then I was sure that it has nothing to do with the bulldoze. It took me a while to effigy out, so here is how you lot tin fix this issue, and clone without whatever trouble.
A bit of background before we go-ahead
I have a Windows 10 PC, which is now 6-7 years old. The past few calendar month's performances started degrading. So, I decided eventually moving to SSD and increased RAM equally the but solution. I wasn't ready to change the complete setup, as it would accept been a waste material of what is still working.
So I got a Samsung 860 EVO 250 GB, plugged into the computer using a SATA wire from the reckoner at home. That'southward when I cloned it for the first fourth dimension, and it worked just fine. The next solar day, I got my new SATA wire, and so I changed information technology on my office computer. When I rebooted, I started getting Blue Screen of Death. I tried booting into rubber mode, and it notwithstanding gave me BSOD. Since I had the previous installation intact on my former HDD, I booted into that, and it worked fine.
I checked for Hd errors, ran the Samsung Magician tool to cheque for SSD errors, but nothing. The start failure occurred after 30 minutes, and the subsequent tries resulted in errors were inside 2-3 minutes. Finally, I decided that it is best to clone it again, and that'due south where things got weird.
Samsung Data Migration: Cloning Failed, An error occurred while reading the disk
When I checked for the fault, about of them were—An error occurred while writing to the TargetDisk.Withal, for me, it was reading the disk.
- Change SATA Port on Motherboard
- Run Chkdisk
- Check for Bad sectors on HDD
I am going to share first what worked for me, followed by a few full general troubleshooting tips which the data migration tool suggested.
1] Change SATA Port on Motherboard
The motherboard of my computer has 4 SATA ports. Out of which two are eSATA ports, while the remainder two are marked as SATA. While I causeless something is incorrect with my wire, I commencement chose to change the port. So I connected it with the red port or eSATA port, which you see in the higher up image. Next, I rebooted the computer, launched the Software Data Migration tool, and it worked.
What still mind boggles me that SATA is used for an internal device connector while eSATA is used as an external device connector. I assume that information technology is a limitation of Samsung Data Migration software, which might demand it to be on the aforementioned type of ports, or information technology looks only for 1st and 2nd drives. The target bulldoze should likely be the secondary internal bulldoze connection.
The summary from Samsung Data Migration tool hints to something similar:
On systems with ii (2) drives or more (e.g. "C:", "D:", and "E:" drives) with the operating arrangement installed on the "C:" drive, only the first two drives volition be cloned. The "System" partitioning that is created during Windows installation is automatically replicated.
I could be wrong, merely changing the port worked, and both HDD and SSD are on the same type of ports. Then it has to hateful something.
two] Run Check Disk tool
Check Disk is an inbuilt tool from Microsoft which can repair disk issues which windows can resolve. To run Bank check Disk on your Organisation Drive (C), using the control line, blazon the following and press Enter key.
chkdsk /f C:
If required, restart your computer. Chkdsk command tin can repair bad sectors if they tin be repaired.
3] Bank check for Bad sectors on HDD
Bad Sectors are part of hard drives that cannot be used to shop information. If you have a bad sector on your HDD, and so the Migration tool will not clone information technology. Tools like Hard Disk Validator can help you discover and confirm. Download the software from the website, and confirm. There are many third-party tools slike Windows Surface Scanner, HD Melody, Macrorit Disk Scanner, EaseUS Division Master Free, AbelsSoft CheckDrive, HDDScan that delivers a better feel.
I promise the postal service truly helped you to fix the problem with the Samsung Information Migration tool, which gives the error — Cloning Failed, An fault occurred while reading the disk . The baseline is to switch the ports and meet what works for y'all. Make certain to power downward the figurer when you lot do that. It's going to exist tedious, only cloning is the fastest style to switch the hard bulldoze.
Source: https://www.thewindowsclub.com/cloning-failed-an-error-occurred-while-reading-the-disk
0 Response to "An Error Occurred While Reading the Disk 301001"
Post a Comment